W&H He-43 Straight Handpiece - HP334

• Robust and durable.
• Autoclavable upto 135C.
• Ergonomic design.
• Simple bur changing.
• Thermo washer disinfectable and sterilizable.
• External coolant supply (spray clip, coolant hose, nozzle cleaner) available as accessories.

• Drive speed: 40,000 min-1
• Motor connection according to standard: ISO 3964
• The outer diameter of the sheath: 20 mm
• Straight handpiece 1:1
• Maximum permitted bur length: Handpiece burs: 50mm, Contra-angle burs: 34 mm
• Spray: single, external

1 x Straight Handpiece

Preparation:

• Ensure the handpiece is properly cleaned and sterilized before each use.

Setup:

• Connect the handpiece to the dental unit or motor, following the manufacturer's instructions for compatibility and proper attachment.

Bur Installation:

• Use the twist tension chucking system to secure the appropriate bur with a Ø 2.35 mm shank.
• Confirm that the bur is securely in place.
  Operational Settings:
• Set the drive speed to the recommended level (e.g., 40,000 min-1).
• Adjust any other operational settings on the dental unit or motor according to the specific requirements of the procedure.

Patient Treatment:

• Hold the handpiece comfortably, considering the ergonomic design to prevent hand strain.
• Perform dental procedures with precision, utilizing the handpiece for efficient and safe treatment.

Coolant System:

• If applicable, connect the external coolant supply system to ensure effective cooling during procedures.

Post-Treatment:

• After use, detach the handpiece from the dental unit.
• Clean the handpiece thoroughly, following the manufacturer's recommended cleaning procedures.
  Sterilization:
• Autoclave the handpiece at the specified temperature (up to 135°C) to ensure proper sterilization.

Maintenance:

• Regularly inspect the handpiece for any signs of wear, damage, or malfunction.
• Lubricate the handpiece as recommended by W&H to maintain optimal performance.

• Country Of Origin: Austria
• Manufacturer: W&H Dentalwerk

• Manufacturer/Importer warranty of 6 months as applicable for this product.
• Service and Warranty are handled by the manufacturer/importer directly for this product
• Oralkart will not be liable to replace the Products and the liability to replace any such Product is that of the Manufacturer/Importer
• Oralkart and the Buyer acknowledge that the Products purchased/usedare a subject matter of original Manufacturer/Importer’s warranties only
• Any or all claims in relation to returns and replacement shall be made to the concerned Manufacturer/Importer only and Oralkart may assist the customer in registering a request to get the Product replaced or serviced.
• The Buyer acknowledges that the Products once sold will not be exchanged or taken back unless the seal of the package or the Product is intact or not altered in any manner or is not tampered as the case may be.

Question: Does the W&H HE-43 Straight Handpiece (HP334) come with a spray clip and coolant hose?Answer: Yes, the W&H HE-43 Straight Handpiece (HP334) comes with a spray clip and coolant hose. These accessories ensure effective cooling during procedures, maintaining optimal performance and comfort for both the practitioner and the patient.

Question: What does 1:1 means?
Answer: The 1:1 gear ratio of the W&H He-43 Straight Handpiece means that the handpiece operates at the same speed as the motor, with no increase or decrease in rotational speed through the gearing system.

Question: Are there additional accessories available for the W&H He-43 Straight Handpiece - HP334?Answer: Yes, accessories such as an external coolant supply (spray clip, coolant hose, nozzle cleaner) are available to enhance the handpiece's functionality.

Question: How can the W&H He-43 Straight Handpiece - HP334 be sterilized?
Answer: The W&H He-43 Straight Handpiece - HP334 is autoclavable up to 135°C, providing a reliable method for sterilization to meet hygiene standards.

Question: Is the W&H He-43 Straight Handpiece - HP334 compatible with common dental burs?Answer: Yes, the W&H He-43 Straight Handpiece - HP334 is designed to accommodate both handpiece and contra-angle burs with a standard diameter of Ø 2.35 mm (ISO 1797-1).