Prime Dental Restorite Nano Hybrid Kit

• Complete solution for composite restoration
• Thixotropic gel consistency for etching
• 5th generation total-etch bonding agent
• Urethane Dimethacrylate-based light-curing composite
• Ultrafine filler for homogenous restorations
• Alumina-based abrasive for efficient polishing
• Precise application and effective conditioning

Restorite Etching Gel

• Formulation: 37% phosphoric acid in thixotropic gel
• Indication: Enamel etching and dentin conditioning

Restorite Bond 5G

• Generation: 5th generation total-etch bonding agent
• Compatibility: Enamel and dentin

Restorite Nano Composite

• Composition: Urethane Dimethacrylate-based
• Filler Load: 83.5% by weight

Physical Properties:

• Volume Shrinkage: 1.3%
• Young's Modulus: 16,575 Mpa
• Bending Strength: 157 Mpa
• Vickers Hardness: 948 Mpa
• Compressive Strength: 432 Mpa
• Tensile Strength: 56 Mpa

Aster Compo

• Abrasive Type: Alumina-based
• Application: Polishing/finishing of composites and enamel
• Properties: Thixotropic, fine grit, mint fragrance

• 1 x 5ml Restorite Bond 7G
• 7 x 4g Restorite Nano Composite Syringes (2 x A1, 2 x A2, 2 x A3, 1 x B2)
• 1 x 3ml Restorite Etching Gel
• 1 x 4g Aster Compo
• 10 x Microbrushes
• 5 x Application needles

Pretreatment:

• Clean the tooth using a non-fluoride polishing paste such as Prime Dental's Aster Prophy.
• Select the shade using a Vita® shade guide while the tooth is still moist.

Cavity Preparation:

• Prepare the cavity minimally as required for adhesive techniques.
• Bevel all enamel margins in the anterior region.
• Avoid beveling margins in the posterior region and slice preparations.
• Clean the cavity by spraying it with water, removing all debris, and drying it.
• Isolate the cavity, preferably using a rubber dam.

Pulp Protection/Cavity Liner:

• Use a calcium hydroxide material to coat areas in close proximity to the pulp in very deep cavities.

Approximal Contact Areas:

• Place a transparent matrix and fix it in place when filling cavities with approximal sections.

Etch:

• Apply Restorite Etching Gel first to the enamel areas of the cavity for 30 seconds.
• Fill the entire cavity (dentine) with Restorite Etching Gel for an additional 15 seconds.
• Rinse the cavity thoroughly with a water spray and dry it with oil-free compressed air.

Bond:

• Apply 2-3 consecutive coats of Restorite Bond 5G to etched enamel and dentin for 15 seconds each.
• Gently air thin for five seconds to evaporate solvents.
• Light cure for 10 seconds.

Composite Filling:

• Extrude the required amount of Restorite Nano Composite from the screw syringe and place it in the cavity.
• Contour the composite. Ensure layers are not thicker than 2 mm.

Curing:

• Light cure all shades for 40 seconds per layer using a light curing unit.
• Hold the light guide as close as possible to the surface of the filling.

Trimming:

• Trim and polish Restorite Nano Composite immediately after curing using finishing diamonds, flexible disks, silicone polishers, and polishing brushes.
• Check the occlusion and articulation and spot grind if necessary.

Final Finish:

• Apply Aster Compo paste on the cup/brush, directly over the tooth, or on the restoration material.
• Use low rotation and low pressure with intermittent touches and circular movements for polishing.

Post-Finishing:

• Apply Prime Dental's Restorite Cavo Surface Sealer to improve marginal integrity by filling microscopic cracks in composite surfaces.

Country of Origin: India Manufacturer: Prime Dental Products Pvt Ltd

• Warranty is not applicable for this product.

Question : What does the Restorite Nano Hybrid Kit include?
Answer: The kit includes Restorite Etching Gel, Restorite Bond 5G, Restorite Nano Composite, and Aster Compo.

Question : Can Restorite Nano Composite be used for all types of restorations?
Answer: Yes, Restorite Nano Composite is suitable for placing fillings using adhesive techniques.

Question : Is the Restorite Nano Composite compatible with other bonding agents?
Answer: Yes, it can be used with Restorite Bond 5G or other bonding agents suitable for composite restorations.

Question : How long does the curing process take for the composite filling?
Answer: Each layer of Restorite Nano Composite should be light-cured for 40 seconds per layer.

Question : Can the Aster Compo paste be used on natural enamel?
Answer: Yes, Aster Compo is designed for polishing and finishing both synthetic restorative materials and natural enamel.

Question : Is it necessary to use a rubber dam during cavity preparation?
Answer: While it is advisable to use a rubber dam, it is not mandatory for using the Restorite Nano Hybrid Kit.

Question : How should the kit components be stored?
Answer: Store all kit contents away from sunlight in a cool, dry place. Some materials may require refrigeration, but freezing should be avoided.