Dentsply Aquasil Ultra Impression Material

• Quadrafunctional hydrophilic addition reaction silicone elastomeric material: This means that the material contains four different types of reactive groups that allow it to bond to surfaces and create an accurate impression.
• Excellent hydrophilic properties: Aquasil Ultra has excellent wetting properties that allow it to flow easily into hard-to-reach areas and capture fine details.
• Dimensional accuracy: The material has high dimensional stability and accuracy, which means that the impressions taken with it are reliable and accurate.
• High tear strength: The material is resistant to tearing and deformation, ensuring that the impression remains intact during the removal process.
• Two types of consistencies: Aquasil Ultra is available in two types of consistencies - light-bodied and medium-bodied - allowing it to be used for a variety of clinical applications.
• Detail reproduction: Aquasil Ultra has a detail reproduction of 20 microns, which means that it can capture fine details and provide accurate impressions.

Composition : 

• Polydimethylsiloxane polymer
• Polymethylhydrogen Siloxane
• Silicon Dioxide
• Sodium Aluminosilicate
• Organic Platinum Complex 
• Surfactant 
• Titanium Dioxide
• Metallic Oxide Pigments
• Peppermint Oil

Technical Specifications :

• Type 3: Light-bodied consistency: Aquasil Ultra XLV, Aquasil Ultra LV
• Type 2: Medium-bodied consistency: Aquasil Ultra Monophase, Aquasil Ultra Heavy
• Working Time (22°C/72°F) : 2'15"–2'45" (Regular set)
• Working Time (37°C/98°F) : 1'10" maximum (Maximum)
• Setting Time (Mouth Removal Time) :  5'00" from start of mix (Regular set)
• Percent Linear Dimensional Change : < 0.50
• Percent Recovery from deformation : .≥ 98
• Detail Reproduction : 20 microns

Dentsply Aquasil Ultra XLV Cartridges (Pk Of 1)

• 1 x 50ml Cartridge 

Dentsply Aquasil Ultra Heavy 50ml Cartridges (Pk Of 1)

• 1 x 50ml Cartridge 

Dentsply Aquasil Ultra Lv Cartridges (Pk Of 1)

• 1 x 50ml Cartridge 

Dentsply Aquasil Ultra Monophase 50ml Cartridge (Pk Of 1)

• 1 x 50ml Cartridge 

Dentsply Aquasil Soft Putty Regular Set 2x450ml + Aquasil Ultra XLV Cartridge set 2 x 50ml (Combo)

• 1 x 450 ml Catalyst
• 1 x 450 ml Base
• 2 Spoons
• 2 x 50ml Cartridge

• Insert cartridge into dispensing gun
• Bleed cartridge before installing new mixing tip
• Single phase impression technique - Assure hemostasis and clean the field with air water spray. Backfill the impression syringe or attach an intraoral tip to the end of the mixing tip. Dispense material into impression tray. Do not overfill tray. Simultaneous with tray loading, syringe completely around the preparation/abutment. 
  
• Regular Set wash and tray material: Loaded tray must be inserted within 1 minute 10 seconds from time of first syringing of wash material intraorally.
•  Minimum Removal Time (from the start of mix) : 5 minutes (Regular Set). If Regular Set Wash is used with Fast Set Tray material, Minimum Removal Time is 4 minutes from start of mix.
• Dual Phase two-step (“putty-wash”) Technique - Complete primary impression with Aquasil Ultra Xtra Tray, Aquasil Putty or Reprosil Tray material. Place one or more polyethylene plastic sheets over the impression material surface. This sheet creates the uniform spacing required for this technique. It also protects the surface from contamination. Insert filled tray into the mouth. Move tray slightly from side to side and back and forth. This creates the spacing for the wash material. Remove tray from the mouth when material has reached a rubbery consistency and set aside. Do not disturb
  impression until fully set. Remove polyethylene sheet, rinse impression with water and air dry. Simultaneous with tray loading, syringe (dentist) completely around the preparation/abutment. Insert filled tray into the mouth.

Question: What is the difference between light-bodied and medium-bodied consistencies?
Answer: Light-bodied consistency is used for syringing around the prepared teeth and margins, while medium-bodied consistency is used for filling the impression tray.

Question: Is Aquasil Ultra compatible with disinfectants?
Answer: Yes, Aquasil Ultra is compatible with most disinfectants.

Question: Can Aquasil Ultra be used for multiple pours?
Answer: Yes, Aquasil Ultra can be used for multiple pours.

Question: Can Aquasil Ultra be used for implant impressions?
Answer: Yes, Aquasil Ultra can be used for implant impressions.