Woodpecker ILED Plus Curing Light (1 Sec Curing Time)

• Constant power output- born for teeth restoration
• 360° curing- reach every angle
• Fluid design- better hand feelin
• 1 sec for curing- 2mm resin
• Wide spectrum emission wavelength range of 385nm to 515nm
• Additional wave band of 385nm to 420nm for better curing of resin materials containing new-style photoinitiators like TPO
• Reduces the risk of resin shedding and incomplete curing
• Suitable for bleached resins and light-colored resin due to the white nature of TPO
• Can effectively cure traditional materials containing camphor quinone(absorbing peak at 460nm) and new materials containing TPO (absorbing peak at 405nm)
• Reduces the need for large amounts of camphor quinonein bleached or light-colored resin
• Provides flexibility to perform both ordinary curing and wide spectrum curing
• Enhanced curing efficiency and accuracy due to the upgraded wide spectrum capabilities

TECHNICAL SPECIFICATIONS:

• Dimensions: 25mm×25mm×240mm
• Net weight: 278g
• Power Input: 100V to 240V, 50Hz/60 Hz
• Wave length: 385nm-515nm
• Light intensity: 1000 mW/cm2~2500mW/cm2

• 1 x Light cure unit
• 1 x Charger
• 1 x Charger cord
• 1 x Instruction manual

• Press the mode button. The following two modes are available.
• TURBO Mode: screen shows P1, Press the time button to select the time which could be 1 or 3 seconds. Its output light intensity is about 2300 mW/cm2-2500 mW/cm2.
• NORMAL Mode: screen shows P2, Press the time button to select the time which could be 5,10,15and 20 seconds. Its output light intensity is about 1000 mW/cm2-1200 mW/cm2.
• During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, and press the ON/OFF button the main unit will produce a "Bi" sound, and the curing light radiates blue light and starts working according to the set modes. Meanwhile, it starts counting down and will produce a tone every 5 seconds, it stops working when counting down to "0".
• During operation, the blue light can be stopped by pressing the power button at any time.
• After a working cycle, the operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to heat obviously, and do not restart until the equipment cools down. Suggest continuing the working cycle less than 10 times.
• The low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of the main unit will wink, please charge in time.
• When the battery needs to be charged, connect the plug of the adapter to the AC100V~240V power supply. Then connect the output plug of the adapter to the DC 5.0V input plug of the pedestal, and then the logo turns blue. Put the main unit to the charging point of the pedestal, the display screen turns to a scrolling display, and the curing lights start charging. When charging is finished, the display screen display "1111".
• After operating, take off the disposable sleeve and throw it away, forbidden to reuse.
• This equipment will turn off automatically if don't have any action within 2 minutes, turn it on by pressing any button.
• The depth of solidification of the composite is no less than 2mm per 1 second.

• Country of Origin: PRC
• Manufacturer: Woodpecker

• Manufacturer/Importer warranty of 1 Year as applicable for this product.
• Service and Warranty are handled by the manufacturer/importer directly for this product
• Oralkart will not be liable to replace the Products and the liability to replace any such Product is that of the Manufacturer/Importer
• Oralkart and the Buyer acknowledge that the Products purchased/usedare a subject matter of original Manufacturer/Importer’s warranties only
• Any or all claims in relation to returns and replacement shall be made to the concerned Manufacturer/Importer only and Oralkart may assist the customer in registering a request to get the Product replaced or serviced. 
• The Buyer acknowledges that the Products once sold will not be exchanged or taken back unless the seal of the package or the Product is intact or not altered in any manner or is not tampered as the case may be.

Question: What is the warranty period for the Woodpecker ILED Plus Curing Light?
Answer: The Woodpecker ILED Plus Curing Light comes with a manufacturer/importer warranty of one year. This warranty ensures that any potential defects or issues within this period are addressed, providing peace of mind and confidence in your investment in this efficient curing light.

Question: What is the significant difference between OLED plus curing unit and ILED Plus curing unit?
Answer: The Woodpecker O LED Plus and iLED Plus curing units are both highly efficient, but each offers distinct advantages. The O LED Plus provides flexible time settings from 1 to 20 seconds and a wide wavelength range of 385nm to 515nm, with extended battery life allowing for over 400 uses per charge. On the other hand, the iLED Plus focuses on speed and precision, with a high intensity of 2300mw/cm² that cures 2 mm of resin in just 1 second. Its extended wavelength range and focused output make it particularly suited for specialized materials like TPO, enhancing efficiency in advanced procedures such as orthodontics and veneers.

Question: Does it have a built-in intensity meter?
Answer: No, the Woodpecker ILED Plus Curing Light does not have a built-in intensity meter.

Question: Does it have a 10 second curing option ?
Answer: Woodpecker ILED Plus Curing Light has two modes: TURBO Mode and NORMAL Mode. In TURBO Mode, the screen shows P1, and the time button can be pressed to select a curing time of either 1 or 3 seconds. The output light intensity is about 2300 mW/cm2 - 2500 mW/cm2. In NORMAL Mode, the screen shows P2, and the time button can be pressed to select a curing time of 5, 10, 15, or 20 seconds. The output light intensity is about 1000 mW/cm2 - 1200 mW/cm2. Therefore, in the second NORMAL Mode, a 10-second curing option is available.

Question: Does the intensity of the curing light decrease with battery drainage
Answer: The Woodpecker ILED Plus Curing Light utilizes a 3.6V/1400mAh rechargeable Lithium battery. Typically, the light intensity remains stable within the specified operational battery voltage range, ensuring consistent performance until the battery approaches its threshold voltage, at which point the light may auto-off.

Question: What is the maximum light intensity of the iLed Plus Wide Spectrum Curing Light?
Answer: The iLed Plus offers a maximum light intensity of 2300mw/cm2.

Question: Can the iLed Plus cure traditional materials as well?
Answer: Yes, the iLed Plus can cure both traditional materials containing camphor quinone (absorbing peak at 460nm) and new materials containing TPO (absorbing peak at 405nm).

Question: How quickly can the iLed Plus cure 2mm of resin?Answer: The iLed Plus can cure 2mm of resin in just 1 second.

Question: Does the iLed Plus offer a comfortable hand feeling during use?
Answer: Yes, the iLed Plus features a fluid design that enhances the hand feeling and ergonomics for an improved user experience.

Question: Which dental procedures is the iLed Plus particularly suitable for?
Answer: The iLed Plus is especially suitable for orthodontic brackets, porcelain veneers, and post-core adhesives.

Question: What is the additional wave band provided by the iLed Plus?
Answer: The iLed Plus offers an additional wave band of 385nm to 420nm, which is beneficial for curing resin materials containing new-style photoinitiators such as TPO.

Question: What is the emission wavelength range of the iLed Plus Wide Spectrum Curing Light?
Answer: The iLed Plus has a wide spectrum emission wavelength range of 385nm to 515nm.