Prevest Mta Plus

• Finer powder for smoother, easier mixing, handling and placement.
• Handy packaging-protects powderin desiccant-lined container
• Optional gel for stability and washout resistance.
• Non-cytotoxic & anti-microbial in vitro against common bacteria and E. Faecails.
• No Special equipment for dispensing instrument needed.

Composition:
Powder consists of mixture of Calcium Oxide, Silicon Oxide, Bismuth Oxide.
Gel is hydrated polymer gel.

Solubility: <2%

Radiopacity: 5 mm equivalent of aluminum

Setting Time at 37°C: < 1 hr. when thickly mixed with gel

Dimensional stability after 30 days: <+0.1% expansion

Film thickness: <50 μm when mixed 1:1 Powder:Gel, otherwise higher.

Compressive strength: 80MPa after 7 days when mixed 3:1 Powder: Gel

Pb and As: < 2 ppm

Prevest Mta Plus trial pack - 1gm:

• 1 x Powder Jar 1g
• 1 x Gel Bottle, 2cc
• 1 x Measuring Spoon
• 1 x Instruction Manual

Prevest Mta Plus Intro Pack - 2gm:

• 1 x Powder Jar 2g
• 1 x Gel Bottle, 2cc
• 1 x Measuring Spoon
• 1 x Instruction Manual

STEP-BY-STEP INSTRUCTIONS:

Dosage and Mixing :

• Dispense 1 scoop of MTA Plus™ powder on a glass slab or a non-absorbent pad.
• Dispense one small drop of MTA Plus Gel, or some of the MTA Plus Liquid from 1 ampoule next to the powder.
• NOTE: The gel imparts washout resistance (for easier rinsing) and faster setting, which the Liquid does not.
• NOTE: MTA Plus Liquid ampoules are larger than unit-dose size.
• Gradually mix the liquid or gel into the powder until the desired putty-like consistency is obtained. For some procedures, a thinner, syrupy, stringy consistency may be desired. Thoroughly mix to hydrate the powder.
• If the material is not to be used immediately, cover the mixed material with a moist gauze sponge (use sterile water), or a clean cover to prevent evaporation. Extra gel or MTA Plus liquid may be used to rewet the powder before it sets.

Precautions :

• AVOID contact of unset mixed paste with skin or oral mucosa. After incidental contact, wash and rinse with water.
• Wear suitable gloves and protective glasses during use.
• MTA Plus™ powder and gel must be kept well sealed.
• PROTECT the powder from humidity. Close the container.
• DO NOT contaminate the powder with an unclean or moist instrument.
• DO NOT overfill the root canals when obturating or sealing.

• Country of Origin: India
• Manufacturer: Prevest Denpro

Question: What is the compressive strength of Prevest MTA Plus after 7 days?
Answer: Prevest MTA Plus exhibits a compressive strength of 80MPa after 7 days when mixed in a 3:1 ratio of Powder:Gel.

Question: What is the setting time for Prevest MTA Plus at 37°C?
Answer: The setting time is less than 1 hour when it is thickly mixed with gel.

Question: Is Prevest MTA Plus soluble?
Answer: Prevest MTA Plus has a solubility of less than 2%.

Question: What is the composition of Prevest MTA Plus?
Answer: The powder consists of a mixture of Calcium Oxide, Silicon Oxide, and Bismuth Oxide, while the gel is a hydrated polymer gel.

Question: Are there any contraindications for using Prevest MTA Plus?
Answer: Yes, Prevest MTA Plus should not be used in cases where the patient has hypersensitivity to caustic (high pH) solutions.

Question: What are the main indications for using Prevest MTA Plus?
Answer: Prevest MTA Plus is indicated for dental procedures involving vital pulp tissue, such as pulp capping, cavity lining, and pulpotomies. It is also used for procedures involving the periradicular tissues, including root-end fillings, apexification, perforation repair, root resorption, sealing, and obturation (pulpectomy).

Question: What is Prevest MTA Plus?
Answer: Prevest MTA Plus is a specialized dental cement composed of Di and Tri-Calcium Silicate. It is used in dental procedures for both vital pulp therapy and endodontics.